Diane (24.209.9.170) - Tue Feb 21 21:52:22 2006

I am trying to find an owners manual for a 1999 Ford Explorer XLT. Just got it and no manual with it. Any clue on getting the fog lights to work?

Reply #1 jDeGuzman (71.135.51.124) - Thu Feb 23 13:45:28 2006

there should be a button on the dash (just right of where the radio is). It is the button just under the rear windshield wiper button.

Reply #2 John (67.160.178.213) - Fri Jan 12 15:02:42 2007

1997 explorer....temperature control knob turns but will not engage heater, any help appreciated

Reply #3 Wayne Thomas (69.107.101.41) - Mon Aug 27 13:47:27 2007

1997 Ford Explorer, looking for the horn fuse. Actually, if you have a fuse diagram, that would be great.

thanks,

Wayne

Reply #4 Peter (74.75.102.156) - Fri Dec 28 16:17:03 2007

I need to make sure my radio antenna cable is properly plugged into the back of my radio. 99 Explorer XLT. AM/FM/CD. I recently hit a deer in the right front quarter. FM is very staticky now and there is no AM reception at all. The body shop said everything looked good at the antenna end when they replaced the fender.

Thoughts? Thanks.

Reply #5 chris gray (72.241.150.198) - Sun May 18 20:26:31 2008

I have a 1999 explorer sport that sounds like it has a spark knock but it is not that.It is not the lifters tapping.It only does between 2300 and 3500rpm.It will do it at an idle.Any Ideas I appreciate it.

Reply #6 amilcar guerrero (66.176.140.63) - Thu Jun 5 16:38:55 2008

wereis locate the fuse box in the ford explorer1999 sport track?

Reply #7 Juan D Triana (24.211.64.215) - Mon Jun 16 15:26:37 2008

Hey, I have 1999 Ford Explorer XLT and I have Transmission issues is good whent I don't give much gas but whent I puch more power whent I need start makeing a noise track track you know wayh I mean can some one help me with an advise? tanks,

also went I put the 4x4 is trying to stuck,

Reply #8 MICHAEL P. MCQUEENEY (70.124.100.10) - Sun Jul 6 23:58:10 2008

1999 explorer stock .How do I wiremy vehicle to keep the driving/fog lights on when I switch on the high beams.There must be a relay.Maybe I need JUMPER WIRE. Please advise THX Mike 210.863.8789

Reply #9 MICHAEL P. MCQUEENEY (70.124.100.10) - Mon Jul 7 00:00:53 2008

1999 explorer stock .How do I wire my vehicle to keep the driving/fog lights on when I switch on the high beams.There must be a relay.Maybe I need JUMPER WIRE. Please advise THX Mike 210.863.8789

Reply #10 Johnny (216.239.87.143) - Mon Jul 14 23:07:26 2008

Reply 8 and 9

Yes, you have to bypass FOG LAMP RELAY tied to + side

of right Drivers Headlamp FUSE 8/10Amp;

cut that wire and tie the relay side to +12V thru fuse

Left and right Headlamps are on separate fuses #4 and 8

(10Amps)

Reply 7: Serious FRONT TRANSFER CASE issue there

Reply 6: Drivers Side dashboard, leftmost surface

right above door hinge is hidden triangular shaped hatch;

all cab fuses are in there, the MAIN fusible link and relay

box is on left fender in the engine compartment

Reply 5:check EGR valve ball freedom of movement

or replace

Reply 4: The Antenna coax is crushed for SURE, because it

goes along that side into the cab and i bet/guess its crushed

at the firewall side; I betcha you have low resitance on center to shield at the radio coax connector and thats a clue

to low RF signal (my guess that the coax cable crush is shortingt the RF signal out, I betcha a screwdriver at the radio RF connector socket center will prove this)

Reply 3: Horn Relay is #10 in the Fuse Block/Engine Compartment, rear side.

Reply 2: 1997 Blower Motor relay circuit, check FUSE #2

7.5A on inside fuse panel, check blower motor relay #9 on the Fuse box in the Engine Compartment , also the big 40A fuse in position #2 in the first row in that front fuse box/Eng.comp.

but if thats blow then perhaps the blower motor is siezed

or perhaps the reostat dash switch assembly has a bad connection

Reply #1: answered correctly, LED is directly connected to ground of the control relay.

I would also like to appeal to find ANY scanned Ford Explorer 1999 Sport 2Door 4L SOHC equipped schematics, and preffer the factory schematics. I have drawings to trade with wiring lists.

Only wish to trade for 1999 data please.

Reply #11 Henry (96.3.191.180) - Thu Aug 14 09:13:34 2008

My overhead compass/temperature doesnt come on, and i pushed the mode button several times, but that doesnt seem to help. Could it possibly be a fuse, and if it could be, which number is it, and what amp fuse do i need to get? Or could it be other things, worked fine up to couple weeks ago.

Reply #12 frank (66.177.239.204) - Fri Aug 15 20:10:16 2008

gas filter change out, is their a canister next to the filter that you can unscrew and clean out water?

Reply #13 frank (66.177.239.204) - Fri Aug 15 20:14:02 2008

2005 explorer which the CD Player will not eject CD is there a way to get the CD to eject without removeing the radio?

Reply #14 frank (66.177.239.204) - Fri Aug 15 20:16:13 2008

2005 explorer which the CD Player will not eject CD is there a way to get the CD to eject without removeing the radio?

Reply #15 Joe (68.55.240.35) - Tue Aug 19 18:27:03 2008

I have a 1995 explorer that is stuck in 4 wheel low I need to know what and how to trouble shoot the problem, control switch, Transfer case motor or what any help would be appreciated

Reply #16 erika voorman (69.125.142.42) - Tue Sep 2 00:20:46 2008

i just got a new door and it has a keypad on it, there's no manual on how to make a lock code or unlock code, can anyone help me out on what the default is or how to unlock itt?

Reply #17 juana (68.199.149.67) - Sat Sep 6 20:08:59 2008

hi; i have a ford explorer '99 2 doors and i dont find the way to put the time in the clock, can someone helpe me please?

Reply #18 malcolm wilson (124.185.141.175) - Sun Sep 7 19:57:51 2008

To release vehicle from 4wd low range you must stop vehicle, turn knob to auto, and put gearbox into neutral or park.wait til 4wd low light goes out on dash then put in drive.Also i have a front transfer case for sale in good condition if anyone interested.

Reply #19 Jim (64.181.89.78) - Mon Sep 8 17:21:03 2008

i got a 95 sport explorer and the cruise control is unhooked. can someone tell me where to find the plugs? much appreciated.

Reply #20 Terrell (207.157.107.126) - Mon Sep 15 13:02:03 2008

I have 1997 Eddie Bauer, Explorer, V-6 , 4 wheel drive, I co not have original owners manuel or any diagram, I cannot find where the brake light fuse is located, and I have the third brake light working, but the main brake light does not, I have replaced the bulbs, and installed new brake light switch but still have no brake light, But the light comes on when the switch is on but no brake lights when the foot brake is applied, Please help, thanks

Reply #21 rt barnes (66.102.234.223) - Wed Sep 17 13:58:36 2008

i have a 1999 ford explorer scout , the seat belt alarm beeps 5 times every 30 minutes when I'm driving.which fuse can I remove to stop this?

Reply #22 Unknown (199.72.141.29) - Wed Sep 24 12:54:21 2008

I had the same problem with the 5 beeps every 30 minutes before, it was a airbag light that was causing it. I changed out the burned light bulb and the beeps became silent.

Reply #23 Nathan Gardner (204.246.203.130) - Wed Oct 8 19:50:52 2008

HELP!

I need a fuse panel diagram for a 1999 ford explorer.

It is a two door sport. I'm looking for the fuse # in

realation to my back up lights. I'd be greatful if anyone out

there could help me out. I bought the explorer a couple of

months ago. It didn't come with manual. If you know where to

purchase one please let me know.

Respectfuly,

Nathan Gardner

Reply #24 Ryan Helbick (138.162.0.42) - Thu Oct 9 10:57:40 2008

99' Ford Explorer XLT, fuse 27 keeps blowing out. It is a 15 amp that controls the reverse lights, overdrive over ride and rear defroster. Does anyone know what else this fuse may control? I am going to replace the reverse bulbs and see if that works. When I replace the fuse and do not use reverse the other components seem to work just fine and do not blow the fuse. Other than replacing the bulbs is there something I might be over looking?

Reply #25 Jose (75.183.25.18) - Sat Nov 1 23:03:23 2008

I can't find the reverse light fuse of my Ford Explorer 2005.

Please ..Any help?

Reply #26 Jacci Demarais (75.168.153.220) - Wed Nov 12 16:22:55 2008

I just bought a 1999 Ford Explorer Sport 2 door, 2wd and it did not come with the owners manual...Where can I get one?

Reply #27 Jacci Demarais (75.168.153.220) - Wed Nov 12 16:25:14 2008

How do I change the keyless pad combo next to the door handle??

Reply #28 Desmond (24.176.20.40) - Thu Nov 20 10:22:52 2008

where is the secondary celleniod located on a 99 ford explorer??? any help appreciated

Reply #29 lory (75.150.101.185) - Fri Dec 12 13:06:59 2008

i have a 2001 ford explorer that didn't come with an owners manual i need to know the wirings of my car so i can install a remote starter but first i need to know what wiring is which so how can i get a wiring diagram for that thanks

Reply #30 Anthony (72.165.223.210) - Fri Dec 19 01:24:19 2008

where is the fill hole to put transmission fluid in the 1999 ford exployer?

Reply #31 amilcar guerrero (68.215.6.14) - Mon Dec 29 00:00:54 2008

need to nreplace dashboard ligths on 1999 ford explorer sport track tks.

Reply #32 felix (24.138.248.61) - Tue Dec 30 01:32:28 2008

i have a 99exploer if i switch to 4x4 high its lights up thats find but when i put it on 4x4 low it still shows that its on high is that normal.if any one has the center console i would like to buy it , in tan color.

Reply #33 Kent (216.85.221.10) - Fri Jan 16 14:05:36 2009

1999 Ford Explorer XLT

My air blow COLD when the Vent Selection is on Max AC, but HOT on all other vent settings. The temp control does not make a difference on any of the vent selections.

Thoughts?

Reply #34 Racheal (70.244.158.132) - Fri Feb 6 20:56:29 2009

We cannot figure out how or where to latch her hooks...does Ford explorer 1999 have child safety hooks to attach her car seat?? if so where are they located??

Reply #35 spencer (69.205.163.143) - Sat Feb 7 00:55:47 2009

anyone know what the little white piece is called, under the steering colomn, that connects to the automatic transmission shifter arm, that moves the needle on the PRND3L?

Reply #36 Lynne (76.116.58.123) - Tue Feb 17 08:43:17 2009

I have a 1999 Ford Explorer 4dr, automatic. My brakes work fine, but I have to press the brake pedal all the way to the floor for the brake lights to come on. Anyone know how to fix this problem?

Reply #37 ickypotcrain (67.176.69.142) - Sun Mar 29 18:59:03 2009

i have a 98 satern 4 door fuse 10 keeps blowing out and it causes the car engin to stop help if you know

Reply #38 Betty Standfill (97.115.133.176) - Sun May 3 16:30:16 2009

I have the beeping problem every 30 minutes. Where di I find the light bulb mentioned in #22

Reply #39 monica (74.94.216.230) - Mon May 11 13:49:01 2009

i have a 2001 for explorer i have replaced the altinator and the battery yet the battery light is still illuminated the manual says electrical system i have tried everything under the sun what is the problem and what do i need to change next because the battery is not charging correctly

Reply #40 marcus (173.169.211.162) - Mon Jun 1 21:48:47 2009

hi could u please tell me where do i find the factory code for the keypad on my 2001 ford explore xlt please

Reply #41 juan (68.205.41.50) - Sat Jun 6 01:05:07 2009

hi i have a 97 ford explorer and my horn doesnt work i dont know what to do the fuse is good. i test the horn with bypass and work but doesnt work with the steering wheel is other fuse or relay i need to replace please i really need it thank you

Reply #42 juan (68.205.41.50) - Sat Jun 6 01:10:26 2009

hi reply #23 you can go to the web ebay.com is 100% you find there good luck

Reply #43 juan (68.205.41.50) - Sat Jun 6 01:26:42 2009

reply #36

yes you need to go where is the brake pedal you will see a small swich just check the swich and ready to go i hope this help you

Reply #44 juan (68.205.41.50) - Sat Jun 6 01:30:35 2009

reply #39

if you change the alternator and the light still on is becouse the alternator is not the right one please check the amperius and you are ready to go i hope this help you

Reply #45 Dutch (96.28.98.55) - Sat Aug 1 18:34:38 2009

99' Ford Explorer max air quit working. When max air is on and you excellerate the duct work changes from vents to defrost. As long as it is on regular a/c everything is fine. Just no max a/c ?. Any advice?

Reply #46 HASIYA (86.179.58.98) - Mon Aug 31 16:24:39 2009

I HAVE A POOR ACCELERATING PROBLEM, DESPITE THE FACT THAT I CHANGE THE FOLLOWINGS;-

PLUGS

FUEL PUMP

FUEL FILTER

SERVICES THE NOSILS.

PLEASE WHAT NEXT?

Reply #47 HASIYA (86.179.58.98) - Mon Aug 31 16:27:57 2009

I HAVE A POOR ACCELERATING PROBLEM, DESPITE THE FACT THAT I CHANGE THE FOLLOWINGS;-

PLUGS

FUEL PUMP

FUEL FILTER

SERVICES THE NOSILS.

PLEASE WHAT NEXT?

Reply #48 cj McAllister (12.69.97.130) - Tue Sep 22 14:51:40 2009

I have a 96 explorer battery went dead I jumped battery, now only the alarm comes on , alarm is aftermarket, I really need to know how to disconnect it w/o creating a bigger problem, PLEASE HELP I have already tried keys, keypad, ect

Reply #49 gel (64.113.121.211) - Thu Oct 1 17:13:06 2009

i have a 99 ford explorer i have lost my running lights my dash lights my o/d and i think it comes back to fuse #33 in the interior fuse box its a gray with a orange stripe wire where does it go and come if someone knows where i can see a wiring diagram for free this would be great

Reply #50 gel (64.113.121.211) - Thu Oct 1 17:16:04 2009

i have a 99 ford explorer i have lost my running lights my dash lights my o/d and i think it comes back to fuse #33 in the interior fuse box its a gray with a orange stripe wire where does it go and come if someone knows how to fix this or where i can see a wiring diagram for free this would be great

Reply #51 sean (65.48.132.98) - Fri Oct 16 17:31:16 2009

how do i reset my ford explorer computer? engine check light is on after transmission was changed. check gage light is on also and an orange light flashes all the time engine is running. have any solutions to my problems. would like to get owners manual.

Reply #52 Frank (75.218.131.33) - Sat Nov 7 00:55:10 2009

I have a 1997 ford explorer XLT the turn signals are not working no , lights whatsoever the hazards do not work eather. I checked all the fuses, what other things can i look at and is there a free manual out there?

Reply #53 Frank (75.218.131.33) - Sat Nov 7 00:55:11 2009

I have a 1997 ford explorer XLT the turn signals are not working no , lights whatsoever the hazards do not work eather. I checked all the fuses, what other things can i look at and is there a free manual out there?

Reply #54 Kevin (68.53.216.81) - Mon Nov 23 13:55:50 2009

I am trying to replace the negative battery cable, and I have traced the wire, but have no idea where the end of the wire is so I can replace it...HELP!

Name:           
E-Mail:         

Optional (please add to our directory first)
Web Link:       
Link Title:     

Message: